1-20 ton gas/oil fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2 Mpa
Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
7-70 MW gas/oil fired hot water boiler
Capacity: 7-70 MW
Pressure: 1.0-1.6 Mpa
Fuel: Nature gas, coke oven gas, blast furnace gas, carbon black off-gas, biogas, methanol, LPG, diesel, heavy oil, light oil, crude oil, etc.
Industries: Heat supplying, hospital, colleges and universities.
2.8-29mw coal fired boiler
Pressure: 1.0-1.25 Mpa
Fuel: Bituminous coal, lean coal, anthracite
Industries: Heating, hotels, schools, hospitals
horizontal thermal fluid heater
Capacity: 700 - 14000 kw
Pressure: 0.8 - 1.0 Mpa
Fuel: natural gas, coke oven gas, bio-gas，liquid propane gas, diesel, heavy oil, light oil, crude oil
Industries: Petroleum, chemical, chemical fiber, pharmaceutical, textile printing and dyeing, building materials, wood processing, vegetable oil processing and other industries
1-20 ton biomass fired boiler
Capacity: 1-20 ton/h
Pressure: 0.7-2.5 Mpa
Fuel: Biomass particles
Industries: Heating, chemical, food, tobacco, textile, printing and dyeing, feed, medicine, building material, wine, rubber, hospital
Shell Boilers - Spirax Sarco
Overview of the different types of shell boiler with layouts, heat and steam release These boilers would now be very expensive to produce, due to the large amounts of These small bore tubes presented a large heating surface to the water. This is made much worse by water with a high TDS level, and accurate control
Boiler Efficiency and Steam Quality: The Challenge of Creating Quality
Steam bubbles are produced at the heat-transfer surface, rising through the water and . Older boilers, while much larger, have a larger steam space which can
Boiler Horsepower - Engineering ToolBox
Heat transfer area and boiler horsepower. of one boiler horsepower is the amount of energy required to produce 34.5 pounds (15.65 kg) of steam per hour at
1 Measurements and Design Enhancements in - Johnston Boiler
for many different things, but the actual steam generation has remained the same. current technology to produce boilers that have an advantage for the A longstanding rule of thumb for firetube boilers is 5 ft2 of heating surface area per boiler the swings were amplified even more and would swing ± 100°F. 2200. 2300.
Optimizing Boiler System Design According to - AEE New England
(C/ I boilers account for as much as 40% of energy consumption) Maintain Clean Water-Side Heat Transfer Surfaces (0-10%). Minimize Radiant Losses Avg. Load Factor over typical production cycle (LF<60% = EE Potential) . Fuel-to-Steam Efficiency (A.K.A. Catalog Efficiency) .. Design: Flame Temp ~ 2,200 oF.
Boiler Blowdown NOD - EPA
Boilers are used to produce steam for the majority of surface vessels that . Auxiliary and waste heat boilers on Navy ships use a feedwater chemical .. surface and bottom blowdowns, the mass of constituents discharged is expected to be much .. 2,200. 58,080. 10,560. 52,800. 121,440. CV 59. 1. 8. 2,000. 17,600. 3,200.
Waste Heat Reduction and Recovery for Improving Furnace Efficiency
Any reduction in furnace heat losses will be multiplied by the overall Hot surfaces radiate energy to nearby colder surfaces, and the rate of heat transfer increases with the . combustion gases, in much the same way cold water added to hot produces warm water. .. option for plants that need a source of steam or.
Superior Boiler - Goes Heating System
Superior is leading the way for green energy with its production of boilers and This simplifies construction, but also loses much efficiency. dimpled heating surfaces, and generous water content, the boiler can Apache-2200-40-HP-2-TransBG With pressures of 15 to 300 psi steam and 30 to 160 psi hot water, the
boiler blowdown management and heat recovery - Texas Cattle
Boilers produce steam and/or hot water as their primary task. paid for the fuel to produce this heat let&39;s reuse it before sending it down the drain. recuperating much of the wasted energy though and save money on fuel costs. .. steam distribution lines and other surfaces running for long distances between the boiler
Improving Process Heating System Performance - NREL
heating accounts for 2% to 15% of the total production cost.2. . Electric-Based Steam has several favorable properties for process heating applications. is a useful attribute in many process heating applications. Steam-based . furnace to produce pig iron. . and melters, but also the surface treatment in ambient air.